Showing posts with label cs. Show all posts
Showing posts with label cs. Show all posts
Thursday, 8 May 2014
Tuesday, 6 May 2014
Sunday, 4 May 2014
The FALKEN'S Pair Drift @ The DRIFT CIRCUIT WIN'S
A lesson in how to get close with the Falken's pair at drift circuit wins
Friday, 2 May 2014
Sunday, 20 April 2014
Pics from today
Some pics of today in Phils garage
Andrew
Ash
Vincent
Patrick
Phil
Vincent
And a few of me Vincent took
Trying to get the Crimson lightning sorted
My Zeon MK3 with Vince's TA06 & LWB Zeon MK4
Andrew
Ash
Vincent
Patrick
Phil
Vincent
And a few of me Vincent took
Trying to get the Crimson lightning sorted
The rigs!
Sunday, 13 April 2014
Friday, 11 April 2014
Rody RC Photos
You would have seen Rody's photos on the internet,top notch photos from Japan. If you haven't already you should like her Facebook page.
Tuesday, 8 April 2014
RC-ART RX rear damper stay
Picked up the new RC-ART RX damper stay features more shock adjustment & has ball end mounting points for camber link adjustment also its 4mm thick over the original 3.5mm.
Keen to get on track and see the difference.
Keen to get on track and see the difference.
Tuesday, 25 March 2014
ZEON CS UP!
With limited CS options available / still in production or actually knowing what fits the zeon without being able to read Japanese it's hard to know how to get a higher CS ratio on the zeon. Zeon and GRK's have very similar gear cases and i think the early GRK'S actually used street jam cases altho i could be wrong.
So i went with some R31 House GRK gears to up my ratio,I already have the Street Jam under drive set for the front that gives you 1.45 CS and have now added added R31 House 19T & 39T gears in the rear to give me 1.73 CS.
I'll give a quick run down of what i did to make the R31 House gears fit the zeon.
First off this is the standard R31 House gear that is modded it also comes with an aluminium 39T ring gear not pictured as there are no mods needed to fit it.
What needs to be done is the lip closest to the teeth needs to be machined/ground back closer to the teeth so that the bearing sits closer to the teeth and the gear doesn't sit so far into the case to allow a proper mesh.
i also took a little off the end of the slotted end of the gear to let the drive cup sit in the proper position. this was done without measurement just test fit and taking small amounts off at time.
So i went with some R31 House GRK gears to up my ratio,I already have the Street Jam under drive set for the front that gives you 1.45 CS and have now added added R31 House 19T & 39T gears in the rear to give me 1.73 CS.
I'll give a quick run down of what i did to make the R31 House gears fit the zeon.
First off this is the standard R31 House gear that is modded it also comes with an aluminium 39T ring gear not pictured as there are no mods needed to fit it.
What needs to be done is the lip closest to the teeth needs to be machined/ground back closer to the teeth so that the bearing sits closer to the teeth and the gear doesn't sit so far into the case to allow a proper mesh.
This is after i ground back the lip so that the bearing can sit further up the shaft it sits in the correct position within the case and meshes with the other gear properly.
The bearing now sits past the first groove you can see on the shaft and meshes with the other gear well within the gear case etc. This all would have been a lot easier with a small lathe and would look alot nicer but it works, it was all done with the gear placed in a drill and a file. I don't take any responsibility for anyone's ruined gears if they want to try this haha it just what i did.
Labels:
countersteer,
cs,
gears,
grk,
mk3,
mods,
ota,
r31 house,
street jam,
zeon
Sunday, 16 February 2014
nakamuraillegalmill 暴走する若者たち(Full Cross編)
Always loved Nakamurailligalmill's videos and its been awhile since we've seen anything from them .
Heres a fresh video the put up yesterday
Heres a fresh video the put up yesterday
Tuesday, 11 February 2014
Last warehouse sliders meet
Well not for good but there wont be any meets at the warehouse for a few months due to space.
And with the local hobby shop dropping their interest in a drift specific track ( even though they have spent money to prep the surface they were going to use ) Were out of a place to drift for now i'm on the search for something tho.Heres the few pics i took of our last meet before my batteries went flat in the camera.
And with the local hobby shop dropping their interest in a drift specific track ( even though they have spent money to prep the surface they were going to use ) Were out of a place to drift for now i'm on the search for something tho.Heres the few pics i took of our last meet before my batteries went flat in the camera.
Wednesday, 5 February 2014
Tuesday, 4 February 2014
CE-RX Update
Stepped up to 1.73 CS on the crimson lightning so that meant i needed to get a front belt tensioner
Also gonna add a little extra weight around the chassis,i started off with 2 small WUN weights mounted in the rear battery mount holes i will add or remove once i run it.
Something new in the post for this too......
Thursday, 30 January 2014
Friday, 17 January 2014
Tuesday, 7 January 2014
Monday, 21 October 2013
First run
Running the 86 body on the CE-RX & changed from Street Jam mediums to hards slowed the car down a bit which a lot of the other guys are starting to do making for some closer driving.
CE-RX & ZEON chilling, zeon had gone from 7 deg castor to 13 deg seemed to make it change direction a lot quicker. I think I'll drop it back to 10deg when I can get my hands on the blue Kazama C hubs.
Friday, 18 October 2013
Subscribe to:
Posts (Atom)






































